(14) Firewall ( Mike )
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
(14) Firewall ( Mike )
Hey Guys,
Just a few Pictures on the process of my Firewall...
Since a lot of people like it... I'll try to explain a little about it.... it's easy to do
.
.
First , I made it from 24 ga Stainless Steel.... ( .024 )
I trimmed it to size before putting the pattern on it ( Engine Turning )
I made a grid that measured 1-1/8" squares....
My Scuff pads were 2 inch..... This way , I didn't wipe out the next row of marks...
One row , you center where the lines "Cross"...
Next row , you go inbetween where they cross....
"MY" project... I went from right to left....
It doesn't matter if it's from left to right....But which ever way you start...
That's the way it needs to be done , the whole way....
.
. Gotta Fly...
.
.
Just a few Pictures on the process of my Firewall...
Since a lot of people like it... I'll try to explain a little about it.... it's easy to do
.
.
First , I made it from 24 ga Stainless Steel.... ( .024 )
I trimmed it to size before putting the pattern on it ( Engine Turning )
I made a grid that measured 1-1/8" squares....
My Scuff pads were 2 inch..... This way , I didn't wipe out the next row of marks...
One row , you center where the lines "Cross"...
Next row , you go inbetween where they cross....
"MY" project... I went from right to left....
It doesn't matter if it's from left to right....But which ever way you start...
That's the way it needs to be done , the whole way....
.
. Gotta Fly...
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
...
...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
.
..
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
.
...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
..
....
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
..
The Bottom Lip was bent first... Then the firewall was put into position...
Then the holes were marked with a transfer punch...
Holes were drilled... then the Firewall was bolted in place to check
where to make the final bends on each side , and the top...
.
.
After the final bends and checking the "fit"
The top corners of the Firewall were welded and cleaned up...
Then the holes were marked with a transfer punch...
Holes were drilled... then the Firewall was bolted in place to check
where to make the final bends on each side , and the top...
.
.
After the final bends and checking the "fit"
The top corners of the Firewall were welded and cleaned up...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
...
...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Last picture
Last but not least , this picture shows how I tilted the firewall forward...
Also... I made it an inch taller on the whole radius...
This will help slope the windscreen more... Less drag
and I like the way the Tailwinds look that use this technic
.
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
.
Also... I made it an inch taller on the whole radius...
This will help slope the windscreen more... Less drag
and I like the way the Tailwinds look that use this technic
.
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- Sean_Caranna
- Founder
- Posts: 231
- Joined: Thu Aug 12, 2004 12:34 am
- Location: Daytona Beach, FL
Re: Firewall ( Mike )
That looks absolutely outstanding!
"I'll have what the gentleman on the floor is having."
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Re: Firewall ( Mike )
Thanks Sean,
This is what it's all about... Taking an regular piece of material , and making something special...
But this design has it's good points.... Hiding Dents , scratches , and dirt...
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
PS I see yer looking for a new plane to build.... Buttercup is pretty easy... a lot of History too ( 1938 )
.
.
.
This is what it's all about... Taking an regular piece of material , and making something special...
But this design has it's good points.... Hiding Dents , scratches , and dirt...
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
PS I see yer looking for a new plane to build.... Buttercup is pretty easy... a lot of History too ( 1938 )
.
.
.
You do not have the required permissions to view the files attached to this post.
Last bumped by planecrazzzy on Fri Dec 31, 2010 9:42 pm.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...