(06) Metal Tubing & Hardware for BC Wings ( Mike )
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
(06) Metal Tubing & Hardware for BC Wings ( Mike )
This will start a new "stage" in the wing building on my Buttercup....
Here's a copy of my order from ACS....This doesn't include the Stainless Steel pieces that I'll need later...
( I'll buy that stuff localy )
03-00810-1 4130 STEEL TUBE 5/16X.058 1FT 1.00 4.300
4.30
03-01200-8 4130 STEEL TUBE 3/8X.035 8FT 2.00 19.600
39.20
03-01200-5 4130 STEEL TUBE 3/8X.035 5FT 1.00 12.250
12.25
03-02500-5 4130 STEEL TUBE 1/2X.049 5FT 1.00 16.500
16.50
03-03600-6 4130 STEEL TUBE 5/8X.035 6FT 1.00 14.700
14.70
03-04300-6 4130 STEEL TUBE 3/4X.035 6FT 3.00 15.600
46.80
03-05500-1 4130 STEEL TUBE 7/8X.058 1FT 1.00 3.600
3.60
03-06200-6 4130 STEEL TUBE 1X.049 6FT 1.00 19.200
19.20
03-07500-8 4130 STEEL TUBE 1-1/4X.035 8F 4.00 28.400
113.60
03-07500-1 4130 STEEL TUBE 1-1/4X.035 1F 1.00 3.550
3.55
03-08300-2 4130 STEEL TUBE 1-3/8X.058 2F 1.00 9.800
9.80
AN970-3 WASHER, FLAT AN970-3 12.00 .070
.84
05-03295 MS51844-24 NICOPRESS ZINC SLEV 16.00 .420
6.72
AN100C-4 SS CABLE THIMBLES AN100C-4 16.00 .210
3.36
05-04400 CONTROL CABLE 1/8 7X19 GALV 50.00 .470
23.50
03-18600 4130 STRIP 3/4 X 72" X .063 1.00 2.880
2.88
03-18900 4130 STRIP 1-1/2 X 72" X .063 2.00 5.760
11.52
03-22520 4130 SHEET .032 9" X 18" 1.00 4.725
4.73
03-23500 4130 STEEL SHEET 9 X 18 X .063 1.00 10.500
10.50
03-24100 4130 SHEET 18"X 36" X .071 1.00 42.000
42.00
FREIGHT ESTIMATED FREIGHT CHARGE 1.00 130.000
130.00
Total Quote: $519.55 USD
This order was estimated "freight" , it will be shipped Cheaper by UPS Ground.....That's why there
aren't any pieces OVER 8 ft long....
Gotta Fly...
Mike & "Jaz" in MN
.
.
. The "Final" cost was CHEAPER than the Quote ( Freight/ UPS )
Everything was under 8' , it was shipped UPS....Total cost - $430.44
After my wings were Built... I order the Bolts and nuts .... Drilled and regular....nylocks & castles , cotter pins , washers
.
The parts ordered are:
QUANTITY BACK NET
PART# ORDERED ORDER PRICE EXT
--------------------------------------------------------------------------------
THANK YOU FOR YOUR ORDER. PLEASE CALL ME DIRECTLY AT
EXT 225 THE NEXT TIME YOU WISH TO PLACE AN ORDER WITH
AIRCRAFT SPRUCE. MARY GARCIA 877-477-7823
.
AN320-3 NUT, SHEAR AN320-3 12.00 0.00 0.470 5.64
AN365-1032A MS21044N3 ELASTIC STOP NUT 22.00 0.00 0.090 1.98
AN365-428A NUT, ELASTIC STOP MS21044N4 30.00 0.00 0.100 3.00
AN365-524A MS21044N5 NUT, ELASTIC STOP 4.00 0.00 0.150 0.60
AN4-15A BOLT UNDRILLED AN4-15A 10.00 0.00 0.350 3.50
AN4-16A BOLT UNDRILLED AN4-16A 2.00 0.00 0.380 0.76
AN4-21A BOLT UNDRILLED AN4-21A 10.00 0.00 0.440 4.40
AN4-6A BOLT UNDRILLED AN4-6A 8.00 0.00 0.140 1.12
AN4-10A BOLT UNDRILLED AN4-10A 2.00 0.00 0.230 0.46
AN970-3 WASHER, FLAT AN970-3 20.00 0.00 0.060 1.20
AN960-10 WASHER, FLAT AN960-10 50.00 0.00 0.020 1.00
AN960-416 WASHER, FLAT AN960-416 50.00 0.00 0.030 1.50
AN960-516 WASHER, FLAT AN960-516 20.00 0.00 0.030 0.60
AN960-616 WASHER, FLAT AN960-616 20.00 0.00 0.040 0.80
AN3-5 BOLT DRILLED AN3-5 4.00 0.00 0.490 1.96
AN3-7 BOLT DRILLED AN3-7 8.00 0.00 0.520 4.16
AN3-22A BOLT UNDRILLED AN3-22A 8.00 0.00 0.370 2.96
AN3-15A BOLT UNDRILLED AN3-15A 2.00 0.00 0.280 0.56
AN3-17A BOLT UNDRILLED AN3-17A 8.00 0.00 0.240 1.92
AN3-20A BOLT UNDRILLED AN3-20A 2.00 0.00 0.350 0.70
AN3-10A BOLT UNDRILLED AN3-10A 2.00 0.00 0.140 0.28
AN6-20A BOLT UNDRILLED AN6-20A 4.00 4.00 0.770 3.08
AN5-12A BOLT UNDRILLED AN5-12A 4.00 0.00 0.340 1.36
AN310-3 NUT, CASTLE AN310-3 12.00 0.00 0.400 4.80
AN365-624A NUT, ELASTIC STOP MS21044N6 4.00 0.00 0.260 1.04
MS24665-132 COTTER PIN AN380-2-2 20.00 0.00 0.020 0.40
----------
TOTAL ORDER 49.78
PLUS APPLICABLE SALES TAX AND SHIPPING CHARGES
Here's a copy of my order from ACS....This doesn't include the Stainless Steel pieces that I'll need later...
( I'll buy that stuff localy )
03-00810-1 4130 STEEL TUBE 5/16X.058 1FT 1.00 4.300
4.30
03-01200-8 4130 STEEL TUBE 3/8X.035 8FT 2.00 19.600
39.20
03-01200-5 4130 STEEL TUBE 3/8X.035 5FT 1.00 12.250
12.25
03-02500-5 4130 STEEL TUBE 1/2X.049 5FT 1.00 16.500
16.50
03-03600-6 4130 STEEL TUBE 5/8X.035 6FT 1.00 14.700
14.70
03-04300-6 4130 STEEL TUBE 3/4X.035 6FT 3.00 15.600
46.80
03-05500-1 4130 STEEL TUBE 7/8X.058 1FT 1.00 3.600
3.60
03-06200-6 4130 STEEL TUBE 1X.049 6FT 1.00 19.200
19.20
03-07500-8 4130 STEEL TUBE 1-1/4X.035 8F 4.00 28.400
113.60
03-07500-1 4130 STEEL TUBE 1-1/4X.035 1F 1.00 3.550
3.55
03-08300-2 4130 STEEL TUBE 1-3/8X.058 2F 1.00 9.800
9.80
AN970-3 WASHER, FLAT AN970-3 12.00 .070
.84
05-03295 MS51844-24 NICOPRESS ZINC SLEV 16.00 .420
6.72
AN100C-4 SS CABLE THIMBLES AN100C-4 16.00 .210
3.36
05-04400 CONTROL CABLE 1/8 7X19 GALV 50.00 .470
23.50
03-18600 4130 STRIP 3/4 X 72" X .063 1.00 2.880
2.88
03-18900 4130 STRIP 1-1/2 X 72" X .063 2.00 5.760
11.52
03-22520 4130 SHEET .032 9" X 18" 1.00 4.725
4.73
03-23500 4130 STEEL SHEET 9 X 18 X .063 1.00 10.500
10.50
03-24100 4130 SHEET 18"X 36" X .071 1.00 42.000
42.00
FREIGHT ESTIMATED FREIGHT CHARGE 1.00 130.000
130.00
Total Quote: $519.55 USD
This order was estimated "freight" , it will be shipped Cheaper by UPS Ground.....That's why there
aren't any pieces OVER 8 ft long....
Gotta Fly...
Mike & "Jaz" in MN
.
.
. The "Final" cost was CHEAPER than the Quote ( Freight/ UPS )
Everything was under 8' , it was shipped UPS....Total cost - $430.44
After my wings were Built... I order the Bolts and nuts .... Drilled and regular....nylocks & castles , cotter pins , washers
.
The parts ordered are:
QUANTITY BACK NET
PART# ORDERED ORDER PRICE EXT
--------------------------------------------------------------------------------
THANK YOU FOR YOUR ORDER. PLEASE CALL ME DIRECTLY AT
EXT 225 THE NEXT TIME YOU WISH TO PLACE AN ORDER WITH
AIRCRAFT SPRUCE. MARY GARCIA 877-477-7823
.
AN320-3 NUT, SHEAR AN320-3 12.00 0.00 0.470 5.64
AN365-1032A MS21044N3 ELASTIC STOP NUT 22.00 0.00 0.090 1.98
AN365-428A NUT, ELASTIC STOP MS21044N4 30.00 0.00 0.100 3.00
AN365-524A MS21044N5 NUT, ELASTIC STOP 4.00 0.00 0.150 0.60
AN4-15A BOLT UNDRILLED AN4-15A 10.00 0.00 0.350 3.50
AN4-16A BOLT UNDRILLED AN4-16A 2.00 0.00 0.380 0.76
AN4-21A BOLT UNDRILLED AN4-21A 10.00 0.00 0.440 4.40
AN4-6A BOLT UNDRILLED AN4-6A 8.00 0.00 0.140 1.12
AN4-10A BOLT UNDRILLED AN4-10A 2.00 0.00 0.230 0.46
AN970-3 WASHER, FLAT AN970-3 20.00 0.00 0.060 1.20
AN960-10 WASHER, FLAT AN960-10 50.00 0.00 0.020 1.00
AN960-416 WASHER, FLAT AN960-416 50.00 0.00 0.030 1.50
AN960-516 WASHER, FLAT AN960-516 20.00 0.00 0.030 0.60
AN960-616 WASHER, FLAT AN960-616 20.00 0.00 0.040 0.80
AN3-5 BOLT DRILLED AN3-5 4.00 0.00 0.490 1.96
AN3-7 BOLT DRILLED AN3-7 8.00 0.00 0.520 4.16
AN3-22A BOLT UNDRILLED AN3-22A 8.00 0.00 0.370 2.96
AN3-15A BOLT UNDRILLED AN3-15A 2.00 0.00 0.280 0.56
AN3-17A BOLT UNDRILLED AN3-17A 8.00 0.00 0.240 1.92
AN3-20A BOLT UNDRILLED AN3-20A 2.00 0.00 0.350 0.70
AN3-10A BOLT UNDRILLED AN3-10A 2.00 0.00 0.140 0.28
AN6-20A BOLT UNDRILLED AN6-20A 4.00 4.00 0.770 3.08
AN5-12A BOLT UNDRILLED AN5-12A 4.00 0.00 0.340 1.36
AN310-3 NUT, CASTLE AN310-3 12.00 0.00 0.400 4.80
AN365-624A NUT, ELASTIC STOP MS21044N6 4.00 0.00 0.260 1.04
MS24665-132 COTTER PIN AN380-2-2 20.00 0.00 0.020 0.40
----------
TOTAL ORDER 49.78
PLUS APPLICABLE SALES TAX AND SHIPPING CHARGES
Last edited by planecrazzzy on Sat Mar 07, 2009 3:15 pm, edited 3 times in total.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Shippment arrived
I got my Shippment today from ACS , Georgia ....( Still waiting for one more piece from Calif )
Everything checks out....Some of the pieces were cut undersize.....some were over... Should be alright.
Here's a few pictures...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
Everything checks out....Some of the pieces were cut undersize.....some were over... Should be alright.
Here's a few pictures...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Ready to Brake & Shear
Hey Guys,
I've got things "preped" to take to work....
I'll use the Brake and the Shear to get good cuts and bends....
The sheet of .071 , was only half (less) used... But the 36" was needed to do that....
( They don't sell 9" x 36" )
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
I've got things "preped" to take to work....
I'll use the Brake and the Shear to get good cuts and bends....
The sheet of .071 , was only half (less) used... But the 36" was needed to do that....
( They don't sell 9" x 36" )
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Getting parts ready
I got quite a few parts ready at work today....
Still have to drill some of the parts , and a little shaping/grinding.
Here's a picture...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
Still have to drill some of the parts , and a little shaping/grinding.
Here's a picture...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- Sean_Caranna
- Founder
- Posts: 231
- Joined: Thu Aug 12, 2004 12:34 am
- Location: Daytona Beach, FL
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Hey Sean...
Hi Sean,
Yeah, it's moving along....Nothin TOO fast , but makin progress....
I'll probably have to ask you for more "Picture MB" before the project is over....
I tend to show alot of detail .....(Good for builders....Bad for byte space...)
Gotta Fly...
Mike & "Jaz" in MN
.
.
Yeah, it's moving along....Nothin TOO fast , but makin progress....
I'll probably have to ask you for more "Picture MB" before the project is over....
I tend to show alot of detail .....(Good for builders....Bad for byte space...)
Gotta Fly...
Mike & "Jaz" in MN
.
.
Sean Caranna wrote:looks like you are moving right along
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Trailing edges
Hey Guys,
I sheared some of the Stainless Steel today...
I need 4 pieces of trailing edge material at 8' long ....
From there , I'll cut two of them to size for the Wing Tips & the Ailerons...
The Flaps will use the 8' pieces ( just shy of 8' )
I couldn't find a "Size" for the trailing edge.... So , I looked at my "tape" , and said that's about right....
So, I sheared my pieces at 3 1/8" wide....That's a 1 1/4" wide trailing edge w/ 5/16 bend each side....
( See picture )
The 5/16 bend REALLY put some strenght to the piece....otherwise it would probably tend to sag in the middle
between where it's welded to the tubing...
The pieces need to be "Closed" a little more....Once I know how much I need , it'll be easy...
The parts are sitting on the 24 gauge material.... see how "flimsy" the stuff is...
Gotta Fly...
Mike & "Jaz" in MN
PS I cut one extra piece....just in case I need it
.
.
.
I sheared some of the Stainless Steel today...
I need 4 pieces of trailing edge material at 8' long ....
From there , I'll cut two of them to size for the Wing Tips & the Ailerons...
The Flaps will use the 8' pieces ( just shy of 8' )
I couldn't find a "Size" for the trailing edge.... So , I looked at my "tape" , and said that's about right....
So, I sheared my pieces at 3 1/8" wide....That's a 1 1/4" wide trailing edge w/ 5/16 bend each side....
( See picture )
The 5/16 bend REALLY put some strenght to the piece....otherwise it would probably tend to sag in the middle
between where it's welded to the tubing...
The pieces need to be "Closed" a little more....Once I know how much I need , it'll be easy...
The parts are sitting on the 24 gauge material.... see how "flimsy" the stuff is...
Gotta Fly...
Mike & "Jaz" in MN
PS I cut one extra piece....just in case I need it
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Piper Channel
I got my "Piper Channel" made today....
I made a few extra.... I think there might be a few needed in the Fuselage.... Not sure
Anywho , I made 16 .... I still have plenty of steel left if I need some more.
I put a penny in the one picture , to give it something to compare to...
I Think I have "gathered" all the parts I need to start "Building" this next stage....
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
I made a few extra.... I think there might be a few needed in the Fuselage.... Not sure
Anywho , I made 16 .... I still have plenty of steel left if I need some more.
I put a penny in the one picture , to give it something to compare to...
I Think I have "gathered" all the parts I need to start "Building" this next stage....
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Lift Strut Brackets
Here's my Lift Strut Brackets....
I'm going to wait on putting the Pipe "Stubs" on them until they're mounted on the spars...
Then I can get them aligned better .
Gotta Fly...
I'm going to wait on putting the Pipe "Stubs" on them until they're mounted on the spars...
Then I can get them aligned better .
Gotta Fly...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Front Spar Connectors
Hey Guys,
I was making the front & rear Spar Connectors.... When I realized the part
that gets welded between the two , were bent to the wrong size....
I was able to salvage two ( from Test Bends ) , So I finished the
Front Spar Connectors...
Here's some pictures...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
I was making the front & rear Spar Connectors.... When I realized the part
that gets welded between the two , were bent to the wrong size....
I was able to salvage two ( from Test Bends ) , So I finished the
Front Spar Connectors...
Here's some pictures...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Wing Tips
Hey Guys,
I'm working on the Wing Tips...
I've got the Spar caps fitting nice and snug...
Next step was to weld the 1 1/4" tubes onto the Spar caps ....and out to a point where the tubes meet...
In order to locate that "Point"..... I've been working on rolling the 3/8" - .035 Tubing
that is for the "Tip" of the wing tip....
Once I locate the "Tip" out in space....I can put the 1 1/4" Tubes where they go...
Anywho,
Bending the Piper Channel radius for the false ribs wasn't easy....
My first attempt was junk....Too Lumpy...
So I made a small "Roller" at work.... for the wheels , I used Bearings
It seems to work very good...
Here's some Pictures...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
I'm working on the Wing Tips...
I've got the Spar caps fitting nice and snug...
Next step was to weld the 1 1/4" tubes onto the Spar caps ....and out to a point where the tubes meet...
In order to locate that "Point"..... I've been working on rolling the 3/8" - .035 Tubing
that is for the "Tip" of the wing tip....
Once I locate the "Tip" out in space....I can put the 1 1/4" Tubes where they go...
Anywho,
Bending the Piper Channel radius for the false ribs wasn't easy....
My first attempt was junk....Too Lumpy...
So I made a small "Roller" at work.... for the wheels , I used Bearings
It seems to work very good...
Here's some Pictures...
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
You do not have the required permissions to view the files attached to this post.
Last edited by planecrazzzy on Sun Jun 22, 2008 6:05 pm, edited 1 time in total.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Wing Tips in "SPACE"
Hey Guys,
I welded the "Tips" together , and I have set it up ( Crude ) to see aprox where it will
be....
I'll find a better way to hold it exactly before I cut and weld the 1 1/4" tubes....
The board that I'm holding it with is warped a little...not good
Here's some pictures...
Gotta Fly...
.
.
.
I welded the "Tips" together , and I have set it up ( Crude ) to see aprox where it will
be....
I'll find a better way to hold it exactly before I cut and weld the 1 1/4" tubes....
The board that I'm holding it with is warped a little...not good
Here's some pictures...
Gotta Fly...
.
.
.
You do not have the required permissions to view the files attached to this post.
Last edited by planecrazzzy on Sun Jun 22, 2008 6:13 pm, edited 1 time in total.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Rib leading edge
Well,
I don't know why these Ribs were made like this.... I got to the point where I had to
cut some wood, Epoxy it and I put a screw in it to hold it.... Then after it dried...I shaped it...
Seems like it would have been stronger if it had been sandwiched with the plywood when the rib was made...
For some reason...That area was vague...
.
.
.
I'm still looking at where to put the bolt hole in the Spar caps.... To keep building
on the wing tip....I put a hole in the spar caps and a screw to keep them snug to the rib....
.
.
.
Here's more Pictures...
.
.
Gotta Fly...
I don't know why these Ribs were made like this.... I got to the point where I had to
cut some wood, Epoxy it and I put a screw in it to hold it.... Then after it dried...I shaped it...
Seems like it would have been stronger if it had been sandwiched with the plywood when the rib was made...
For some reason...That area was vague...
.
.
.
I'm still looking at where to put the bolt hole in the Spar caps.... To keep building
on the wing tip....I put a hole in the spar caps and a screw to keep them snug to the rib....
.
.
.
Here's more Pictures...
.
.
Gotta Fly...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Wing Tip
Here's a start....I've got one tube holding the "TIP" in place...
.
.
.
.
.
.
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
More Wing Tip
More tubes in the Wing Tip...
Gotta Fly...
Gotta Fly...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...