SuperStol Bad Parts ??

CanadianSheepHunter · Sat Nov 30, 2019 12:30 am

Anyone ever had any bad parts?...Last night I took my Aileron bellcranks out of sealed bag and right away noticed the groove on the side of bolt hole, now tonight while taking pics I found cracks !!...I can feel the biggest crack with my fingernail !

CanadianSheepHunter · Sat Nov 30, 2019 12:35 am

They are closed til Monday so I haven’t had a chance to see what factory says.

CanadianSheepHunter · Sat Nov 30, 2019 12:52 am

This is the other Aileron Bell Crank, both holes where the AN3-5 go have a vertical groove like a cable could make...both of these came out of a sealed bag !

CanadianSheepHunter · Sat Nov 30, 2019 12:55 am

The bag my Bellcranks came in.

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:08 am

Aileron pulley Notch on perimeter edge

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:11 am

Same Pulley

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:13 am

Same Aileron Pulley...came out of a sealed bag.

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:23 am

I just figured might as well take pics of the bags

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:32 am

Aileron Hinge Point Brackets came in this sealed bag...strange grooves on bolt hole edges on 8 of the 12 holes !

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:34 am

Same Aileron Hinge Point Brackets

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sat Nov 30, 2019 1:40 am

Same Aileron Hinge Point Brackets AAW-0143 Pics without flash

danerazz · Post by **danerazz** » Sat Nov 30, 2019 9:26 pm

The hole issues look like a laser cutter issue, and some of the marks look like they could be made by a cutter head contacting the part.

EDIT:

The pulley also looks like a CNC cutter starting point gone wrong. The CNC shop looks like they need some adjustment...

AV8R Paul · Post by **AV8R Paul** » Sat Nov 30, 2019 9:39 pm

I’d pack up the parts and send them back and ask for a replacement. Make sure you list all of the pieces you are sending back. I’m positive the factory will replace them.

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sun Dec 01, 2019 3:08 am

danerazz wrote:The hole issues look like a laser cutter issue, and some of the marks look like they could be made by a cutter head contacting the part.

EDIT:

The pulley also looks like a CNC cutter starting point gone wrong. The CNC shop looks like they need some adjustment...

Ok thanks

CanadianSheepHunter · Post by **CanadianSheepHunter** » Sun Dec 01, 2019 3:12 am

AV8R Paul wrote:I’d pack up the parts and send them back and ask for a replacement. Make sure you list all of the pieces you are sending back. I’m positive the factory will replace them.

Yes for sure I would think there would doubt they will replace, the parts for this kit were built 2013/2014 as far as when he picked it up from factory( I bought a kit that a guy started building on in 2014)

B_Wings Forum

B_Wings Forum

SuperStol Bad Parts ??

SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??

Re: SuperStol Bad Parts ??